Real niches have curves

Niches in the round are a great option for trophy rooms and other architectural centerpieces.

Many of us are finding ourselves rounder in the new year, and niches are no exception. Mixing up the geometry gives players more niches to love, and we're all about architectural body acceptance.

Grab the files
Patreon
Thingiverse
MyMiniFactory

Files are available now via Dropbox to our Patreon supporters. Files are posted to Thingiverse and MyMiniFactory later, as time permits. Check back if you don’t see them right away.

An elegant weapon for a more civilized age

Illuminated wall-mounted lightsaber display

Feeling kinda cute. Might slaughter all the younglings. IDK. This 3D-printed wall mount with programmable LEDs holds one of our lightsabers. Photo by Monica Jones

During our trip to Disneyland last year, Devon and I made custom lightsabers at Savi’s Workshop. Devon also bought a replica of Rey’s weapon, and I bought him a Darksaber for Father’s Day.

This is the way to a lot of lightsabers.

Don’t look at us like that. Normal people have lightsaber collections, and there’s nothing weird to see here.

A collection without a way to display it is just vendor trash, so Devon 3D printed wall mounts for our budding Jedi-Sith armory.

Supplies

Free STL files
Silk Silver PLA
Protopasta Steel Filled PLA
Hatchbox Black PLA
Overture clear PETG
Diffusion film
Right angle USB-C cable, 10 ft
Threaded inserts (M2 for grate, M3 for clip)
Socket-cap screws (M2 for grate, M3 for clip)
Heat-set insert tips
Soldering iron Make sure it's one compatible with the tips you get
Solder
ESP 8266 board, USB-C
Seed LEDs Amazon, AliExpress (We used the ones from AliExpress)
Wet or dry sandpaper, 150, 220, 400, 800, 1500, 3000 grit
Double-sided mounting tape
Pixel String Light
WiFi Development Board

Instructions

The seed pixels (the LEDs) have three wires. The marked one is for voltage, which gets soldered to the 5v hole on the ESP. The next one is for signal. I soldered that to D4. The final wire is for ground, and that one gets soldered to G.

Cut as much wire as you need for your project. We recommend using no more than 30 LEDs on an ESP board.

Next, install WLED on the board. You’ll need to install the drivers first. Then plug in WLED and follow their setup instructions. Your config should look something like this.

Sand the grate, moving up from 150 to 3000 grit, to get a realistic metallic shine.

Use thin strips of mounting tape to stick the LEDs inside and to hold the ESP on the back. Position it so the right-angle USB cable can seat reasonably.

Use a soldering iron to sink in the threads, and attach the clip to the front side of the grate.

Cut the diffusion paper to size, and sandwich it between the base and the grate. Attach the grate with the screws.

PRINTING NOTES

The mounts were printed on a Bambu, utilizing the AMS to use multiple filaments in the same print. If your printer can’t auto-swap filament, you can switch manually part way through the print.

The grate was printed using Silk Silver PLA with Protopasta Steel Filled PLA on the top four layers.

The clip was printed with Hatchbox Black PLA. The body was printed with the same, but Devon also used Overture clear PETG for the support interface to simplify removing the supports.

Masterwork Tools is an Amazon Affiliate. We earn a small commission on qualifying purchases.

It's no one's goddamn business why you need a steel cage

Break up your Dungeon Stone design with circular grates.

Tired of all your gated rooms looking like crab cages? Mix them up with curves for circular gardens, prisons, gladiator tournaments and boss fights.

Grab the files
Patreon
Thingiverse
MyMiniFactory

Files are available now via Dropbox to our Patreon supporters. Files are posted to Thingiverse and MyMiniFactory later, as time permits. Check back if you don’t see them right away.

Let your creepy light shine

Skyrim's Dragonpriest mask, with custom lighting

This 3D-printed Dragon Priest mask is illuminated with programmable LEDs. Photo by Monica Jones

Before Christmas, Devon dove back into an old hobby — electronics — when he strung year-round programmable LEDs across the front of our house. Now he must illuminate all the things, and nothing is safe.

This Skyrim-inspired 3D-printed Dragon Priest mask, designed by Jtm, has been guarding our office, waiting for the sweet, sweet touch of LEDs. Today, this creepy severed head shall wear purple.

Supplies for Electronics

Pixel String Light
WiFi Development Board
Soldering Station (or whatever station you have)

Instructions

The seed pixels (the LEDs) have three wires. The marked one is for voltage, which gets soldered to the 5v hole on the ESP. The next one is for signal. I soldered that to D4. The final wire is for ground, and that one gets soldered to G.

Cut as much wire as you need for your project. We recommend using no more than 30 LEDs on an ESP board.

Next, install WLED on the board. You’ll need to install the drivers first. Then plug in WLED and follow their setup instructions. Your config should look something like this.

Configuration specs for programmable LEDs

Masterwork Tools is an Amazon Affiliate. We earn a small commission on qualifying purchases.

Everything is better with a portcullis

Add a portcullis to this 3D-printable curved stone wall to keep out the riffraff. Release includes concave and convex walls.

We want one of these for our real-life home, but it's probably against HOA regulations. So we live vicariously through tabletop gaming.

Add one -- or more -- to your curved walls for extra drama.

Grab the files
Patreon
Thingiverse
MyMiniFactory

Files are available now via Dropbox to our Patreon supporters. Files are posted to Thingiverse and MyMiniFactory later, as time permits. Check back if you don’t see them right away.